Gas cutting manipulator CAVG
Gas cutting manipulator CAVG
Electromechanical valve for automatic shut-off of gas supply.
Key features
| Dimensions | 100 x 90 x 70 mm |
| Nominal voltage | 12 VDC |
| Operating voltage | 8VDC – 16VDC |
| Operating power | 0,24W – 4,5W – 10W |
| Consumption | 20mA-350mA- 1000mA |
| Torque | 10 – 30 – 40 KG/cm |
| Temperature | -20ºC ~ +50ºC |
| Humidity | <95% RH |
Technical Data Sheets
Manuals
External power supply ZAFIRPWS
External power supply ZAFIRPWS
External power supply (with built-in battery charger) for fire detection, certified according to EN 54-4.
This equipment is especially indicated to adequately power any element of the fire detection system that requires external power supply.
Key features
- Low profile, overall height less than 53.4 mm (including socket).
- Also available with high socket for 20 mm pipe.
- Double red alarm LED, which allows to identify the detector in alarm status from any direction (360º).
- Possibility of connection to a remote action indicator.
- Easy connection, no polarity.
- Indication, by means of LEDs, of the communication with the control panel (single blinking), as well as of the alarm status (LEDs on).
- Signaling of the sensor’s soiling status on the control panel display (the sensor allows differentiation between rapid signal increases due to alarm and small, slow and sustained increases due to accumulation of dust and dirt).
- Easy-to-install head and socket, interchangeable across the entire A30X range, and made of heat-resistant white ABS.
- Certified by AENOR according to EN 54 part 7 and CE marked according to the European Construction Products Regulation (EU) Nº305/2011.
Technical Data Sheets
Manuals
BT-24 Batteries
BT-24 Batteries
12 Vdc batteries for power supply of Cofem’s fire detection and alarm system.
Key features
-
Both fire panels and external power supplies require two 12 Vdc batteries connected in series.
There are different references according to the capacity required:
- BT-2402: Set of 2 batteries of 12 Vdc with capacity of 2 Ah.
- BT-2406: Set of 2 batteries of 12 Vdc with capacity of 6 Ah.
- BT-2415: Set of 2 batteries of 12 Vdc with capacity of 15 Ah.
- BT-2424: Set of 2 batteries of 12 Vdc with capacity of 24 Ah.
Technical Data Sheets
Manuals
External Power Supply PWS03 / PWS05
External Power Supply PWS03 / PWS05
External switching power supply (with built-in battery charger) for fire detection.
There are 2 models depending on the power requirements of the system:
- PWS03: 3A (100W) power capacity.
- PWS05: 5A (155W) power capacity.
The PWS is offered installed inside a 418 x 324 x 150 mm box, which provides additional space for the necessary batteries inside the box.
Key features
- Power capacity of 3A (model PWS03) or 5A (model PWS05).
- FAE incorporated in a box, which allows the necessary batteries to be installed inside the box.
- Reduced dimensions of the box: 418x324x150 mm.
- Metal box.
- Built-in battery charger.
- Existing variant with cassette in gray color.
Technical Data Sheets
Manuals
Battery box C88
Battery box C88
Box to contain the batteries of the fire detection and alarm system when they cannot be placed inside the fire panel.
Key features
- Metallic chest painted in black color and with the door in gray.
- Dimensions: 418 x 324 x 150 mm.
Technical Data Sheets
Manuals
External power supply PWS PWS03Y / PWS05Y
External power supply PWS PWS03Y / PWS05Y
External Power Supply (with built-in battery charger).
There are 2 power supply models depending on the needs of the system:
- PWS03Y: 3A(100w) power supply capacity.
- PWS05Y: Power capacity of 5A(155w).
The PWS is installed inside a box measuring 416 x 321 x 132 mm (without door), which provides additional space for the batteries inside the box.
Key features
- Power supply voltage: 110 230V/AC 50Hz
- Output voltage: 27.4 ~ 27.8 V/AC
- Output current: PWS 03: 3A / PWS 05: 5A
- Battery charger: Yes
- Humidity: 20 – 95% RH
- Temperature: -10ºC + 50ºC
- Dimensions: 424 x 330 x 140 mm
- IP protection: IP 30
Technical Data Sheets
Manuals
Electromagnet ELPCF fire doors
Electromagnet ELPCF fire doors
Equipment to control the closing of fire doors allowing sectorization in case of fire.
There are different references depending on the material (steel or aluminum) and the delay, as well as adjustable arms of different lengths:
Key features
ELECTROMAGNETS ELPCF50K-ELPCF50KR-ELPCF50KAL-ELPCF50KALR:
Electromagnetic wall retainers for fire doors.
- Power supply: 24 Vdc.
- Consumption: 60 mA.
- Holding force: > 55 Kg | adjustable force.
- Unlocking button.
- Noise suppressor.
- Antimagnetic spring.
- UNE 1155 certificate.
- Head dimensions: 75x90x35 mm.
ELECTROMAGNET ELPCF140K:
Electromagnetic wall retainers for fire doors:
- Power supply: 24 Vdc.
- Consumption: 70 mA.
- Holding force: > 140 Kg.
- Unlocking button.
- Noise suppressor.
- Antimagnetic spring.
- Certified according to EN 1155.
- Head dimensions: 90x100x43 mm.
ELPCF300K ELECTROMAGNET
Electromagnetic door damper for emergency doors and passage doors in general, high power.
- Power supply: 12 – 24 Vdc.
- Consumption at 12 Vdc: 500 mA.
- Consumption at 24 Vdc: 250 mA.
- Holding force: 300 Kg.
- With cushioning.
- Operating temperature: -10ºC to +50ºC.
- Protection: IP40.
- Dimensions: 250 x 48x 25 mm.
ELPCF600K ELECTROMAGNET
Electromagnetic door damper for emergency doors and passage doors in general, high power.
- Power supply: 12 – 24 Vdc.
- Consumption at 12 Vdc: 500 mA.
- Consumption at 24 Vdc: 250 mA.
- Holding force: 600 Kg.
- Dimensions: 265 x 66 x 41 mm.
ELPCF50KS ELECTROMAGNET
Electromagnetic retainer for floor mounting.
- Power supply: 24 Vdc.
- Consumption: 45 mA.
- Holding force: 50 Kg.
- Protection: IP40.
Technical Data Sheets
Manuals
Sign Plates
Sign Plates
PL-FC501: Photoluminescent PVC plate 210x297mm fire extinguisher
PL-FC511: Photoluminescent PVC plate 210x297mm fire hydrant
PL-FC515: Photoluminescent PVC plate 210x297mm alarm button
PLFC525: Photoluminescent PVC plate 210x297mm alarm bell
PLFT711: Photoluminescent PVC plate 297x105mm exit
PL-F: Various plates (consult) dimensions 210x297mm
Key features
Technical Data Sheets
Manuals
Accessory and battery case C88Y
Accessory and battery case C88Y
Box to contain the accessories and batteries of the fire detection and alarm system when they cannot be placed inside the fire panel.
Key features
- Metallic box painted in white color.
- Dimensions: 424 x 330 x 140 mm.
Technical Data Sheets
Manuals
Socket for detectors D50Z0 and D50ZAL
Socket for detectors D50Z0 and D50ZAL
Socket for fire detection and alarm detectors of the A50 and C50 range.
There are 2 versions: with low socket or with high socket (prepared for connection with 20 mm diameter pipe).
Key features
- Low profile, overall height less than 53.4 mm (including socket).
- Also available with high socket for 20 mm pipe.
- Double red alarm LED, which allows to identify the detector in alarm status from any direction (360º).
- Possibility of connection to a remote action indicator.
- Easy connection, no polarity.
- Indication, by means of LEDs, of the communication with the control panel (single blinking), as well as of the alarm status (LEDs on).
- Signaling of the sensor’s soiling status on the control panel display (the sensor allows differentiation between rapid signal increases due to alarm and small, slow and sustained increases due to accumulation of dust and dirt).
- Easy-to-install head and socket, interchangeable across the entire A30X range, and made of heat-resistant white ABS.
- Certified by AENOR according to EN 54 part 7 and CE marked according to the European Construction Products Regulation (EU) Nº305/2011.